Driver Message Center

ICU4Me

Functions

ICU4Me settings and the driver message center are controlled using the switches mounted in the left-hand switch pod of the steering wheel. See Fig..

The driver message center is divided into four sections. The odometer and cruise control status field are displayed along the bottom of the message center. When cruise control is active, the cruise control status field displays relevant cruise control icons and the set speed. If the vehicle is equipped with a manual transmission, time and temperature are displayed in the top left corner of the driver message center. The message field displays the driving screens and alert messages. See Fig..

If the vehicle is equipped with an automated transmission, the gear display is located in the top left corner of the driver message center. Time and temperature are displayed in the message field, unless an alert message is active or a driving screen has been selected. The odometer and cruise control status field are displayed along the bottom of the message center. See Fig.. For information about transmission display options, see Detroit™ Multifunction Control.

Alert Messages

Alert messages are displayed in the message field to notify the driver when certain conditions occur. They include warnings, cautions, and other messages that require the driver’s attention. Not all alert messages are critical to the operation of the vehicle. More important messages take priority over less important messages.

Press the OK button on the left-hand steering wheel pod to acknowledge alert messages and revert to the previously displayed driving screen. The following alert messages will repeat intermittently until the condition is eliminated:

• turn signal on

• low voltage

• no datalink

• low transmission air pressure (Detroit transmissions only)

Driving Screens

With the parking brake off, only the driving screens are available. Use the UP and DOWN navigation switches on the steering wheel to scroll through the driving screens; see Fig.. To reset any values, press and hold the RIGHT navigation switch.

• Temperature

• MPG information

• Trip information

• Leg information

• Gauge display (if selected)

• Predictive Cruise Control (optional)

• Enter parked menus

Parked Screens/Menus

Park the vehicle and set the parking brake to access the parked menus and submenus. See Fig.. To reset values in any of the menus, press and hold the RIGHT navigation switch.

• Trip information

• Fuel information

• Engine information

• Diagnostics

• Service information

• Settings

• ICU Information

A small numerical fraction is displayed in the upper right-hand corner of each screen to indicate the number of available screens or options to scroll through. See Fig.. Press the OK button on the left-hand steering wheel pod to select a menu choice. Press the LEFT navigation switch to back out of a selected menu or submenu. Use the UP navigation switch to scroll up, and the DOWN navigation switch to scroll down.

When navigating the parked menus, the left side of the driver message center displays a "breadcrumb menu" to show the order of menus and submenus that have been selected during the current navigation.

Trip Information

The ICU can record data for one trip segment and one leg segment. When trip information is reset, all the leg information is reset as well.

Fuel Information

Using this menu, the driver can view the total fuel used since the last reset, the total idle gallons used since the last reset, and the average MPG since the last reset.

Engine Information

Using this menu, the driver can view engine miles, engine hours, gallons used, PTO hours, and PTO gallons. Engine oil level is optional for Detroit engines. The information contained in the Engine Information screens cannot be reset.

Diagnostics

Active faults are displayed in the diagnostics menu. See Fig.. If there are any active faults, the total number of faults is displayed in parenthesis next to the affected controller. To view specific active faults, press the OK button on the left-hand steering wheel pod. Press the OK button to toggle between the text description and the failure code for each selected fault.

Service Information

Using this menu, the driver can enable, disable, and set service intervals for engine miles or engine hours. After enabling service intervals, select interval unit (miles or hours), and the interval duration.

Settings

The settings menu contains the controls for the following settings:

• Display (includes brightness, display light, and night mode settings)

• Gauge select

• Language

• Temperature warning enable/disable

• Units

The Gauge Select submenu allows the driver to select certain gauge values for display in the message field while driving. See Fig.. Use the UP and DOWN navigation switches on the steering wheel to scroll through the list of available gauges, then press the OK button to select a desired gauge. The OK button can also be used to uncheck boxes if necessary.

ICU Information

The ICU Information screen displays the part numbers for the instrument cluster and software.